Welcome Guest [Log In] [Register]
Welcome to NYTHIRDGEN. We hope you enjoy your visit.


You're currently viewing our forum as a guest. This means you are limited to certain areas of the board and there are some features you can't use. If you join our community, you'll be able to access member-only sections, and use many member-only features such as customizing your profile, sending personal messages, and voting in polls. Registration is simple, fast, and completely free.


Join our community!


If you're already a member please log in to your account to access all of our features:

Username:   Password:
Add Reply
U-joint job
Topic Started: Jul 14 2009, 09:03 PM (225 Views)
JekyllandHyde
Member Avatar
SENSEI
Well, got out from under the GTA and found that my driveshaft is a little loose... turns out that a worn u-joint was the cause of intermittent clunking when I shift from park into drive. How much should I expect to pay for a u-joint job? I'm hoping CK Peformance does this work... I want him to tackle my shift kit job at the same time.
Currently looking for a 91-92 Z28, TTA or GN
Offline Profile Quote Post Goto Top
 
Formula388
Member Avatar
Senior Technical Advisor
I would say about an hours labor plus parts... just a guess... the shift kit is going to be more obviously...
Offline Profile Quote Post Goto Top
 
klowny
Member Avatar
Da Klownfather
I've done plenty of u joints..real easy..piece of cake for ck performance....the part is not expensive twenty thirty bux i believe...



Check out my thirdgen videos and technical how to vids...from basic car maintenance to Performance mods..
subscribe (its free to subscribe) and you will be updated on future projects:

https://www.youtube.com/watch?v=6HO-D0aIgx8

https://www.youtube.com/watch?v=mIx1TqfXt6A

Thanks!
Offline Profile Quote Post Goto Top
 
charged355
Member Avatar
Nythirdgen Founder
i didnt see a lift when i went to pick up my tranny, but then again i didnt really look around :lol:
Posted Image

Custom Forged 355 / Solid roller cam/valvetrain / Victor Jr heads / Hurricane Intake/ Accufab 1250cfm Throttle body / MegaSquirt 3 Engine Managment/ 1000cc SouthBay Injectors/ 7.6:1 CR / 4" Custom Single Exhaust / 4000 Circle D Stall/ CK Performance Billet 4L80 FMVB Trans Brake / 3" Chromoly Driveshaft / Full UMI Tubular Rear Suspension / Moser/Strange 9" / 4:11 gears Detroit Locker / Sumped LS1 gas tank / A1000 Fuel pump / A1000 FPR / Paxton Fuel filter / -10 Fuel line -8 return / Borg Warner S475 Turbo @10psi/ JGS 50mm WG & 56mm BOV / PA Racing Complete Tubular Front End Kit With Coilovers / Full Autometer Dash / Custom Black Suade Guts / Built by yours truly/ Tuned by George the EFI whiz

http://www.youtube.com/channel/UCnxlPhzRElZYM5YE-n2NRUw
Offline Profile Quote Post Goto Top
 
klowny
Member Avatar
Da Klownfather
i havent been to his new shop..but his old one he had four five lifts...tell em manny sent ya...the greek with the camaro ;)



Check out my thirdgen videos and technical how to vids...from basic car maintenance to Performance mods..
subscribe (its free to subscribe) and you will be updated on future projects:

https://www.youtube.com/watch?v=6HO-D0aIgx8

https://www.youtube.com/watch?v=mIx1TqfXt6A

Thanks!
Offline Profile Quote Post Goto Top
 
1 user reading this topic (1 Guest and 0 Anonymous)
« Previous Topic · Transmissions and Drivetrain · Next Topic »
Add Reply

Black Water created by tiptopolive of the Zetaboards Theme Zone